Brand:TE Corcom
MOQ:1
Quantity:100
Send Inquiry
ED Series- Two element circuit provides medium attenuation
- Available with an internal ground-circuit inductor (C versions)to isolate equipment chassis from power line ground at radiofrequencies
- Versions up to 15A
- Similar to EEJ Series with alternative termination options
- See the EC Series for better differential mode performance
Ordering Information
Available Part Numbers
| 1ED1 | 1ED2 | 1ED4 | 1ED8 |
| 3ED1 | 3ED2 | 3ED4 | 3ED8 |
| 6ED1 | 6ED2 | 6ED4 | 6ED8 |
| 10ED1 | |||
| 15ED1 | 15ED8 | ||
| GroundCircuitInductor Versions | |||
| 6ED1C | 6ED4C | 6ED8C | |
| 10ED1C | |||
Specifications
| Maximum leakagecurrent, each Line toGround: | ||
| @ 120 VAC 60 Hz | .22 mA | |
| @ 250 VAC 50 Hz | .38 mA | |
| Hipot rating (oneminute): | ||
| Line to Ground | 2250 VDC | |
| Line to Line | 1450 VDC | |
| Operating Frequency: | 50 / 60 Hz | |
| Rated voltage(max.): | 250 VAC | |
| Rated Current: | 1A to 15A | |
| Operating Ambient Temperature Range(at rated currentIr): | ||
| -10°C to 40°C | ||
| In anambienttemperature (Ta) higher than 40°C the maximum operating current (Io) is calculated as follows: Io = Ir √(85-Ta)/45 | ||
Electrical Schematic
AccessoriesGA400: NEMA 5-15P to IEC 60320-1C13 line cord
FA601: Insulating Shroud
Case Styles
ED1 & ED1C
| Typical Dimensions: | ||
| Mounting holes (2): | .132 [3.35] Dia. | |
| Line Inlet (1) | IEC60320-1 C14 | |
| Terminals (2): | .250 [6.35] with .07 [1.8] Dia. hole | |
| Ground Terminal (1): | .250 [6.35] with .07 x .16 [1.8 x 4.1]slot | |
ED2
| Typical Dimensions: | ||
| Mounting holes (2): | .132 [3.35] Dia. | |
| Line Inlet (1) | IEC60320-1 C14 | |
| Terminals (2): | .250 [6.35] with .07 [1.8] Dia. hole | |
| Ground Terminal (1): | .250 [6.35] with .07 x .16 [1.8 x 4.1]slot | |
ED4 & ED4C
| Typical Dimensions: | ||
| Mounting holes (2): | .132 [3.35] Dia. with .236 [5.99] Dia. x90º countersink for #4 flathead screw | |
| Line Inlet (1) | IEC60320-1 C14 | |
| Wire Leads (3): | 4.0 [101.6] Min., 18AWG, UL1015 | |
ED8 & ED8C
| Typical Dimensions: | ||
| Mounting holes (2): | .132 [3.35] Dia. | |
| Line Inlet (1) | IEC60320-1 C14 | |
| Wire Leads (3): | 4.0 [101.6] Min., 18AWG, UL1015 | |
Recommended Panel Cutouts
Note 1: ED1 and ED8 allow for front or backmounting
Note 2: ED2 and ED4 allow for back mounting only
Case Dimensions
| Part No. | A | B | C | D | E | F |
| (max.) | (max.) | (max.) | ± .015 | (max.) | (ref) | |
| ±.38 | ||||||
| 1ED1, 3ED1, 6ED1 | 2.21 | 1.19 | 0.81 | 1.575 | 1.98 | |
| 56.0 | 30.2 | 20.6 | 40.01 | 50.3 | ||
| 1ED2, 3ED2, 6ED2 | 1.55 | 1.19 | 0.85 | 1.575 | 1.98 | |
| 39.4 | 30.2 | 21.6 | 40.01 | 50.3 | ||
| 1ED4, 3ED4, 6ED4 | 1.55 | 1.19 | 0.85 | 1.575 | 1.98 | .295 |
| 39.4 | 30.2 | 21.6 | 40.01 | 50.3 | 7.5 | |
| 1ED8, 3ED8, 6ED8 | 1.55 | 1.19 | 0.81 | 1.575 | 1.98 | .295 |
| 39.4 | 30.2 | 20.6 | 40.01 | 50.3 | 7.5 | |
| 6ED4C | 1.98 | 1.19 | 0.85 | 1.575 | 1.98 | .295 |
| 50.3 | 30.2 | 21.6 | 40.01 | 50.3 | 7.5 | |
| 6ED8C | 1.98 | 1.19 | 0.81 | 1.575 | 1.98 | .295 |
| 50.3 | 30.2 | 20.6 | 40.01 | 50.3 | 7.5 | |
| 6ED1C, 10ED1, 10ED1C 15ED1 | 2.62 | 1.19 | 0.81 | 1.575 | 1.98 | |
| 66.5 | 30.2 | 20.6 | 40.01 | 50.3 | ||
| 15ED8 | 1.98 | 1.19 | 0.81 | 1.575 | 1.98 | |
| 50.3 | 30.2 | 20.6 | 40.01 | 50.3 | ||
