Brand:Bosheng
MOQ:2000
Quantity:10
Hitachi carbon brush,HITACHI 999041, carbon brush for powertools,power tools carbon brush,carbon brush replacement
| Size | 6.5X7.5X13/14.5mm |
| Code NO. | BS-99-041 |
| Original NO. | 999041 |
| For model | BLUSH3,DMT-13A,BUW-SH3,C5,C5Y,D6SH, D10VC,D13T,DH16V,DH22VB,DH22VD,DH24PB,DH24PD, DD-13V,DH24VB,DH-24VD,DMT13A,DR10,DU10,DUT10, DUT13,DUV10,DUV13,16,DV13V,DU14V,DU20T,DV20V1, DV20V2,DDV20V3,DV20VA,DVR10,DVR13,DV14V,DV20T,DV20V1, DU20V2,DV20V3,DV20VA,DVR10,DVR13,DW15Y,D10VD, D13V,D13VB,D-6C,D-10C,D10V1,DG-6,D-6V,DG-8,DY-6, D-10V,D-10VA,DM-13A,DV-10,DMT-13,DMV-13,DL-1GA, D-1FA,DH-14V,DV-20V,FC5SSA1,FCH66,FCJ55,FCJ55VA, FCJ65V,FDV12T,FDV12V,FDV15V,FDV15V,FM8,FDU16VA,FH45, FDV20VA,FH35SA,FJ50SR,FJ50VA,F20SA,FS10SA, FS10SB,FSV12,SFV13Y,FV16V,FV20V,FSV12V,FD10VA, FDV15T,FDV16V,FD10SA,FDV15T,FV12T, FV12VA,FV12VB,FU-20,LUH7,LUT-DM4,NUDH4,P20V, P20SA,PH22V3,SN6,SNG-6,SN-10,A,UT5V,VTP10,VTP13, VTP13A,VTV10,VTV13A,V-14,VP-14,V-10A,W6V1,W6V2, W6VA,W6VA2,W6VB,W6VE,W6VE,W6VF,W6SC,W6VA1,W6, W6SA,W6V,DH18VB,DH24PE,DV20VB,W6VB2,W8VB
|
power tools carbonbrush
we can supply various kinds of power tools carbonbrush,our carbon brush has characters,used such as long time,low spark.
Products manufactured by automatic carbon brush machines,characteristics as follows:
1. From the appearance point of view: chamfer decent product,appropriate structure standard specifications, the wire’scross-section and length, not loose, falling off, broken off side,off angle, clamp and so on.
2. From the use of terms:
(1) Graphite products using high-quality, long life and do not wearcommutator or slip rings, commutator never appears scratch,rough, ablation and so on.
(2) With a good flow properties and set to change commutation , sothat spark suppression in the permitted range, and the energy lossis small.
(3) When carbon brush runs, no heat, noise, broken, what’s morenever change color carbon brush‘s body, no ablation.
(4) During the running, It can make the surface of commutator orcollector ring quickly form a uniform, moderate and stable oxidefilm.
Non-standard brush can be designed and be manufactured perbuyer's drawing or sample.
Information for your reference
Carbonbrush performance
Commutator:
Unit must be in good condition, with less than .002"out-of-roundness. Bar edge must be chamfered and there should be noburned edges.
Brush Holders:
They must be mechanically sound and permit the brush to slidefreely. Brush holder fingers must move freely and if the unitconsists of constant pressure springs, these springs must be ingood condition. Springs that are difficult to move, have anexcessive accumulation of carbon, or are worn, will cause excessivebrush wear.
Brush Holder Angles:
Theangles should be set to the original manufacturer's specification.Any more than a 2 degree variation in the setting can cause arcing,bar burning, and excessive wear. Brush holders that vary in theangle set to the commutator will cause the unit to be "offneutral".
Brush Holder Spring Tension:
Maintaining the proper spring pressure reduces arcing, brush wear,heating, and commutator wear. Light spring tension can causethreading and definitely will shorten the brush life. As a generalrule, we recommend that the brushes be set at 4 psi pressure. Tocalculate the pressure, measure the width and thickness of thecontact face and calculate as follows:
Pressure in Pounds/Brush = (Width x Thickness x 4 psi)
Brush Holder Quartering:
To insure that the best machine electrical neutral can be achieved,the brush holders must be quartered. Quartering is setting thebrush holders at equal distance around the commutator. For a 4 polemachine, the spacing will be every 90 degrees. If the quartering isnot properly set, you may experience excessive arcing, heating,brush wear, and commutator wear.
Machine Neutral:
To obtainoptimum machine performance, the brush must be set at the machineelectrical neutral. If the unit is off neutral, you may observesparking under a no-load condition. Depending upon how far offneutral the machine is set, there may be arcing and barburning.
Carbon BrushesDescription The Principal Dimensionsof a Carbon BrushNote:
We work to NEMA and ANSI tolerances on the dimensions given to us.Width and thickness dimensions should be established accurately. Ifin doubt, it should be noted that the internal dimensions of thebrush holder should be about .003" greater than the nominaldimensions of the brush.Flexible length is the length from the topof the longest side of the brush to the center of the terminalhole.The dimensions of "d" on the double shank terminals may varywith the flexible size, reducing as the flexible size increases andthe minimum permissible dimension should bestated.Terminals:
Please givethe size of opening.
Hitachi carbon brush,HITACHI 999041, carbon brush for powertools,power tools carbon brush,carbon brush replacement
