Description:
Decorative and Energy-Saving 12 x 1W LED Downlight for Home andOffice UseThis minimalist design Crystal LED downlight comes as a completefitting, incorporating a solid powder coated aluminum lamp body,LED emitter, heatsink, and external 240VAC mains powered lowvoltage 320mA DC driver.
The 3W 240VAC LED downlight uses a standard Epistar (1 yearwarranty) or Edison (2 year warranty) Chip module, but the largeheatsink design allows the LED emitter to be driven harder for anequivalent standard halogen lamp output of over 60 Watts, yet usesonly a fraction of the electricity to run and will outlast up totwenty five standard halogen GU10 lamps. This Warm White /White model is supplied fitted with a wide 30 degree 9 unit clearlens for a focused, crisp beam of light, similar to a tungstenhalogen lamp. A frosted lens is available as an optionalaccessory.
With their high light output and wide beam angle, we expectthese lamps to primarily be of interest for those designing new lowenergy lighting projects. However, depending on the design ofyour existing GU10 lamp fittings, it may be possible to retro-fitthese lamps into existing lighting installations. If youintend to replace existing fittings with these lamps, please checkthat original ceiling cutout is the same size or smaller beforeordering.
1. Input Power :100VAC~240VAC (Voltage Alternating Current)
2. Electron Reversal Flow per second: 50~60Hertz (i.e. VACcurrent in wall socket is reversing directions 50 to 60 times persecond. Standard Reversal)
3. Rate of Constant Current required: 350mA
4. Actual current required must be equal to or greater than320mA (i.e. 0.32 Amperes or more is required to power the LEDdownlight. Very low electricity usage)
5. Color Temperature from Downlight (i.e. color appearance ofthe downlight bulb itself and the light it produces): 3000K to3700K for warm white (color output is warm or red-yellow-whiteappearance), 6000K to 8000K for white (color output is close tosunlight at noon on a clear day)
6. Lumen measurement (i.e. the power of light perceived by thehuman eye): 510lux (per 6 Square Feet and 9 feet height fromdecorative ceiling to floor – Industry requirement is 320lux to500lux for office lighting, 80lux for toilet lighting, 50lux forliving room lighting. 400lux is usually the measurement of lightduring sunrise or sunset on a clear day). To increase the lumenmeasurement within the room, use more downlights per 4 squarefeet)
7. Useful life of Crystal LED Downlight: more than 40000continuous hours of use
8. Warranty on LED (Chip) Lamp only: 1 Year for Epistar Chip, 2years for Edison Chip. Just send us back the whole LED Downlight(unrepaired) to our offices, and we will send to you a NEWreplacement at minimum transport cost by using our partnertransport company.
9. Size of 12 x 1W LED Downlight: Round shaped. 137mm inDiameter. 68mm in height (therefore requires the vertical spacebetween the decorative ceiling board to slab concrete ceiling to be75mm or 7.5cm, or more, for proper installation of LED Light ontoceiling board). A cut out on the ceiling board of 120mm in diameteris required for the fixing of this LED Downlight.
10. Power Consumption per LED Downlight: 9 units of 1 Watt = 9Watts per LED Downlight - CSSAC516220L212W5PTHhas 12 LED bulbs per Downlight whereby 1 LED bulb uses 1 watt ofelectricity. (12 Watts LED Downlight produces superiorlighting brightness as compared typical household incandescentlight bulb (25 watts to 100 watts) and fluorescent lamp (5 watts to30 watts).
11. Chip Type: Epistar Chip or Edison Chip (Higher Quality).
12. Angle Adjustment: LED Downlight can be adjusted up to 30degree angle tilt.
13. Certification: Crystal LED Downlight comes with CE RoHSCertification (i.e. Conformite Europeenne on Restriction ofHazardous Substances for Electrical Products). (CE Certification isrequired for all manufactured products sold in Europe. Any LEDproduct that is CE certified means that those LED productssatisfies all requirements of European health, safety andenvironmental directives laid down by European legislation).
14. Usage: LED Downlight to be connected to power source in thesame way as any other lighting is connected. only for use withON/OFF switches - Not suitable for dimmer switches.
Target Clientele: We are happy to sell to lighting retailers orfor use in project works.
Samples: Customers are welcome to purchase sample units fortheir evaluation and testing. Upon acceptance of performance ofsample product, we shall export our Minimum Order Quantity (MOQ)and above to your desired trading address.
Minimum Order Quantity: 1 unit for Sample. 20 units and abovefor wholesale. Prices vary for sample and wholesale units.
Payment Terms: Full payment before commencement ofproduction.
Upon confirmation of receipt of full payment of order, ourfactory will produce the order and test each individual Crystal LEDDownlight accordingly. Each individual LED Downlight will befurther tested by our Electrical Engineers upon delivery to ourDistribution Centre in Penang, Malaysia, before transport anddelivery to the customer.
