Description:
It is used for produce A/B/C, A/B/C/B/A style PP.PS.PE plasticsheet.KHSJP120-100-65B(1200mm T-Die)
main parameter
1.suitable sheet:PP.PS, PE.
1, sheet thickness:0.3~2.0mm.
2, max. sheet width:1000mm.
3, maximum output:500kg/h.
4 sheet: fourlayer.
parameter of machine
A. extruder:
A.1output:50kg/h.
A.2 screw:diameter 65mm. ratio:30:1, RPM:120max.
A.3 screw and drum:materialL:38CrMoALA, nitrogen treatment.
A.4 motor:22kw AC motor,
A.5 heating:10KW, 4section with aluminum heaters;
A.6 cooling: 120W/220V with 4 section;
B. extruder:
B.1output:200kg/h.
B.2 screw:diameter 100mm. ratio:33:1, RPM:100max.
B.3 screw and drum:materialL:38CrMoALA, nitrogen treatment.
B.4 motor:75kw AC motor,
B.5 heating:22.5KW, 5section with aluminum heaters;
B.6 cooling: 120W/220V with 5 section;
C. extruder:
C.1output:3500kg/h.
C.2 screw:diameter 120mm. ratio:33:1, RPM:90max.
C.3 screw and drum:materialL:38CrMoALA, nitrogen treatment.
C.4 motor:75kw AC motor,
C.5 heating:45KW, 7section with aluminum heaters;
C.6 cooling: 180W/220V with 7 section;
2. filter changer:
A mesh changer
A.1 by electric with two station.
A.2 material:38CrMoALA nitrogentreatment.
A.3 heating power::4kw
A.4 Mesh changer alarm: pressure sensor setup thepressure, exceed the setup pressure will inform to change the meshby giving an alarm .
B mesh changer
B.1 by electric with two station.
B.2 material:38CrMoALA nitrogentreatment.
B.3 heating power::6kw
B.4 Mesh changer alarm: pressure sensor setup thepressure, exceed the setup pressure will inform to change the meshby giving an alarm .
C mesh changer
C.1 by electric with two station.
C.2 material:38CrMoALA nitrogentreatment.
C.3 heating power::6kw
C.4 Mesh changer alarm: pressure sensor setup thepressure, exceed the setup pressure will inform to change the meshby giving an alarm .
3. die head:
3.1 T-die.
3.2 valid width:1200mm.
3.3 material and heat treatment:high-quality steel, surface withchrome platen, Thickness is 0.02~0.03mm, HARDNESS:HV≥850.
3.4 rough:Ra0.05μm.
3.5heating power:10kw
3.6 extruder pressure: through the pressure sensorshow the extruder pressure.
3.7 pressure closed-loop control system: use thepressure sensor setup the pressure, and through the pressureself-adapt meter control extruder motor speed, reach relativestable extruder pressure, so that stable the output.
4.Roller temperature controlsystem
4.1 Cooling medium:Water
4.2 Temperature:Normal-90°C
4.3 Heatingpower:3*9KW
4.4 Waterpump:0.75KW centrifugal pump
4.5 Flux: Control bysolenoid valve
6. Autoloader:
6.1new material autoloader:200kg;
6.2recyle material autoloader:400kg;
6.3gloss material autoloader:50kg;
7. calender
7.1 roller: diameterφ460mm, length:1500mm, rough Ra0.025μm,surface with chrome platen, hardness: HRC≥55.
7.2 vertical type by hydraulic.
7.3 drive by gear which run by chain, converter speedadjust.
7.4speed:20M/min.
7.5cooling roller: diameter φ270mm, length1500mm,
7.6 temperature control: controlled by waterheating and cooling system.
8.Pull system:
8.1 pull roller:10xΦ50x1500mm
8.2 rubber rollerhardness: ≥A60
8.3 diameter of rubberroller:200mm
8.4 speed:22M/min
8.5 pull motor: 0.75kw
8.6 static eliminatesystem: 1000mm static eliminator
8.7 web material rewinddiameter : Φ500mm,
8.8 cut knife: rise and fall, widthall can be adjusted, easy operation
9.rewinder:
9.1 motor:1.5kw.
9.2 tension control:magnetic clutch.
9.3 unwinding motor:0.55Kw.
9.4 diameter:φ800mm;
9.5 diameter of inner core:φ76mm.
9.6 rewinder speed:22M/min
